UltiMaker Factor 4 Plus Upgrade Kit

Description

The UltiMaker Factor 4 Plus Upgrade Kit turns the Factor 4 you already own into a Factor 4 Plus. The upgrade is about speed: UltiMaker rates the Factor 4 Plus at up to 2× the print speed of a standard Factor 4, across all materials including composites, with no loss of dimensional accuracy. The kit combines a new vibration-absorbing gantry, high-flow AA+ and CC+ print cores and firmware that runs UltiMaker's Cheetah motion planner. It also includes a permanent license for UltiMaker TRACE, which logs and validates every print.

The build volume stays the same (330 × 240 × 300 mm), and so does everything else you rely on: the heated chamber, the material handling, Digital Factory and your existing print cores.

Factor 4 vs. Factor 4 Plus: what the kit changes

Factor 4
After the upgrade (Factor 4 Plus)

Print speed
Standard
Up to 2× faster

Gantry
Original XY gantry
Re-engineered gantry built to absorb vibration at high speed

Motion planning
Standard
Cheetah motion planner removes abrupt motion changes that cause vibration

Print cores
Standard AA, BB, CC and HT cores
High-flow AA+ 0.4 mm (2×) and CC+ 0.6 mm (1×) included; standard cores still work

Process validation
Not included (Print Process Reporting sold separately)
Permanent UltiMaker TRACE license included

Build volume
330 × 240 × 300 mm
Unchanged

Digital Factory
Connected
Stays connected; the printer updates to Factor 4 Plus automatically

A gantry built for speed

The new XY gantry module is the most important part of the kit. Printing fast shakes a machine, and vibration is what costs accuracy, so the gantry is built to absorb it. The included firmware adds the Cheetah motion planner, which takes out the abrupt changes in motion that cause vibration in the first place. Together they let the printer move much faster while holding its dimensional accuracy.

High-flow print cores

AA+ 0.4 mm (2 included): an internal quad-chamber design delivers about 2.5× more flow for fast, detailed prints in the full range of non-abrasive materials, such as PLA, Tough PLA, PETG and ABS. The cores are tuned for the Cheetah motion planner.

CC+ 0.6 mm (1 included): an abrasion-resistant nozzle for carbon- and glass-fiber composites, such as PPS CF, at high speed and up to 340 °C.

With three cores you can run two high-flow cores, or one high-flow core next to a dedicated BB support core. You only get the full speed increase with AA+ or CC+ cores installed.

UltiMaker TRACE included

UltiMaker TRACE (Technical Reporting And Certification Engine) continuously measures four key factors of every print: extrusion factor, nozzle temperature, build-volume temperature and build-plate temperature. It flags small thermal or volumetric deviations that could affect part quality, layer adhesion or mechanical performance, and it produces a digital report for each job. That makes it useful for the documentation that production, aerospace and defense work require. The license is permanent. You activate it through an UltiMaker account, but the printer itself doesn't have to be networked or added to Digital Factory.

What's in the box

Main items

Gantry module (Factor 4 Plus XY motion system)

Print core AA+ 0.4 (2×)

Print core CC+ 0.6

USB drive with the Factor 4 Plus upgrade firmware

UltiMaker TRACE license

Installation and maintenance pack

Torx 20, Hex 2 and Hex 2.5 screwdrivers

Small mirror (for purge calibration)

Grease and linear guide rail lubricant

UltiMaker cleaning filament pack (10×)

Purge rubbers (2×)

Nozzle cover pack (6×)

Printed quick start guide

Installation: about 30–40 minutes

The upgrade is designed for Factor 4 owners to do themselves, using the tools in the kit:

Power off and unplug the printer.

Remove the old gantry and slide in the new one (four captive screws, two cables).

Install the Factor 4 Plus firmware from the included USB drive.

Run the lift switch and gantry calibrations.

Swap in the AA+ and/or CC+ print cores.

Run the purge location and XY offset calibrations.

Activate your TRACE license.

Add the Factor 4+ in UltiMaker Cura if the printer isn't connected to Digital Factory.

UltiMaker's step-by-step upgrade guide and installation video cover each step.

Good to know before you buy

Check your gantry version. This kit includes the new gantry, which every Factor 4 with the original (V1) gantry needs. Running Factor 4 Plus firmware on a V1 gantry isn't supported and can damage the machine. If your Factor 4 already has the V2 gantry, there's a kit without the gantry. Contact us with your serial number and we'll confirm which kit you need.

The firmware change is one-way. Once the printer runs Factor 4 Plus firmware, it can't go back to Factor 4 firmware.

Your existing files and cores still work. The upgraded printer accepts jobs sliced for the Factor 4, though parts may come out slightly differently because the printer now uses the Cheetah motion planner. Standard AA, BB, CC and HT cores remain compatible.

Splash screen: the boot

SKU
240600 (3D Universe)

Vendor Pricing & Availability

3D Universe

Updated: 1 hour ago

$3,500.00

Free Shipping

Buy Now →

Store links may be affiliate links: we may earn a commission at no extra cost to you.

Advertisement

Price history

Lowest price each day

$3,500

Collecting price history

We have one day of prices so far. The trend line appears after at least two days.

View as table
Date 3D Universe
Nov 17, 2026 $3,500

Advertisement

Zeb · 1d ago

Message hidden until you log in.
B

bob · 1d ago

Message hidden until you log in.
B

bob · 1d ago

Message hidden until you log in.
B

bob · 1d ago

Message hidden until you log in.
B

bob · 1d ago

Message hidden until you log in.
B

bob · 1d ago

Message hidden until you log in.

Eck · 23h ago

Message hidden until you log in.

7 recent messages, hidden until you log in. Log in or sign up to read the chat and join in.

Send private messages to other members.

Log in