LDO LCP300-48 300W 48V Compact Power Supply (PSU)

Description

The LCP300-48 is a compact, fully enclosed 300W output power supply for 3D printing applications. Featuring Power factory correction and Gallium Nitride technology, the LCP300-48 provides 48V outputs with an efficiency of over 90%.

Features

Output: 48VDC (4pin+, 4pin-)

Highly compact (120×95×35mm) and fully enclosed

GaN technology with PFC and efficiency of up to 91%

Overload, overvoltage, output short-circuit, and temperature protection

Wide AC input: 100-240VAC

Dual AC input terminals, Supports AC parallel connection

Model Breakdown

Electrical Specifications

Model
LCP300-48

Output
Output Voltage
48V

Max Current
6.25A

Rated Power
300W

Ripple & Noise (Max)2

360mVp-p

Line Regulation
±1%

Load Regulation
±2%

Start-up / Rise Time3

3000ms/115VAC,≤100ms/220VAC

Hold-up Time4

≥8.3ms

Input
Voltage Range
100 - 240VAC

Frequency Range
50-60Hz

Efficiency
≥91%

AC Current
3.5A/115VAC 2A/230VAC

Inrush Current
≤80A/220VAC cold start

Leakage Current
≤0.75mA, 240VAC/50Hz

L/N Terminal Current5

12A Max

Protection Features
Overload Protection
≥110% of rated output power

7.2-11.25A (48V), output voltage shuts off; recovers automatically after fault removal

Output Short-circuit Protection
output voltage should shuts off without causing damage to the power supply; recovers automatically after fault removal

Overvoltage Protection
≥135% of rated output voltage

Output voltage shuts off; recovers automatically after fault removal

Temperature Protection
When enclosure surface temperature exceeds 110°C

Output voltage stops until temperature drops below 80°C

Environmental Conditions
Operating Temperature
-20~50℃

Operating Humidity
20~90%RH

Storage Temperature & Humidity
-30~85℃/ 10~95%RH

Vibration
10-500Hz, 2G, 10 minutes/cycle, 60 minutes in each X, Y, and Z direction

Safety & Compliance
Safety Standards

High Voltage Resistance
2.5KVAC

Insulation Resistance
≥100MΩ

EMC Immunity
Compliant with EN/IEC: EN55032, EN55035

Harmonic Standards
Compliant with IEC61000-3-2, IEC61000-3-3

LVD
Compliant with EN IEC 62368-1

FCC

Compliant with FCC 47 CFR Part 15 Subpart B

ANSI C63.4:2014

WEEE
Compliant with Directive 2012/19/EU

Others
Dimensions
120.0mm (L) * 95.0 mm (W) * 35.0 mm (H)

Packaging
137x105x39mm

MTBF
50000h (25℃)

Notes

Unless otherwise specified, all specifications are measured under 230VAC input, rated load, and 25°C ambient temperature.

Ripple and noise measurement: Measured at the end of the output cable, with a 0.1μF ceramic capacitor and a 47μF electrolytic capacitor.

Start-up time: The time from when power is applied to the input until the output voltage rises to 90% of its rated value. Rise time: The time required for the power supply to reach its rated output value from a no-power state.

Hold-up time: The duration from when the AC input is cut off to when the output drops below 5% of the standard value.

L/N terminal current: Refers to AC voltage interface, where a single input is used to distribute one output. The maximum current the AC voltage interface can withstand is 12A.

Wiring & Connections

AC (Mains) Input

The LCP300-48 accepts a wide input range from 100-240VAC. There is no input voltage selection switch required.

The LCP300-48 features dual AC input terminals. Each terminal is capable of transferring currents of up to 12A. This allows for additional AC loads to be daisy chained through the power supply, greatly simplifying wiring.

The input connectors use M3 barrier terminals. SV2-3 or equivalent fork spade terminals are recommended for wiring.

Output Terminals

The LCP300-48 features four 48VDC output terminals.

A total combined output of 310W is possible. However, at maximum output, the power supply can become significantly hot, and external airflow directed at the casing is recommended in this situation.

The output connectors use standard screw terminals. While bare stripped wires can be used, it is highly recommended to use ferrules. Ferrules up to size VE1508 can be used.

Drawings and Dimensions

A 3D CAD model is provided here.

For more information please see the LDO Docs. Datasheet can be found here.

SKU
LDO5401 (West3D)

Vendor Pricing & Availability

West3D

Updated: 5 hours ago

$68.99

Free Shipping

Buy Now →

Store links may be affiliate links: we may earn a commission at no extra cost to you.

Advertisement

Price history

Lowest price each day

$68.99

Collecting price history

We have one day of prices so far. The trend line appears after at least two days.

View as table
Date West3D
Nov 17, 2026 $68.99

Advertisement

Zeb · 1d ago

Message hidden until you log in.
B

bob · 1d ago

Message hidden until you log in.
B

bob · 1d ago

Message hidden until you log in.
B

bob · 1d ago

Message hidden until you log in.
B

bob · 1d ago

Message hidden until you log in.
B

bob · 1d ago

Message hidden until you log in.

Eck · 1d ago

Message hidden until you log in.

7 recent messages, hidden until you log in. Log in or sign up to read the chat and join in.

Send private messages to other members.

Log in