colorFabb PLA/PHA Filament 2.85mm (750 g) - Blueish White / 2.85mm
Description
Overview
colorFabb PLA/PHA
PLA/PHA: colorFabb's signature blend of bioplastics.
A less brittle and stunning PLA filament.
Specifications
Material:
colorFabb PLA/PHA
Diameter Tolerance:
± 0.05 mm
Density:
1.210-1.430 g·cm-3
Glass Transition Temperature:
55C
Printing Advice
At colorFabb we have a well equipped 3d printing studio with a lot of popular 3d printers. We know our materials will give you excellent results and to help you get these results here are tips and trick for using colorFabb 3d printing filament.
Advised 3D printing temperature
195-220℃
Advised 3d print speed
40 - 100 mm/s
Advised Heated bed
50-60C
Build platform
Our PLA/PHA performs well on both heated and non-heated build platforms. For those users printing on a cold build platform we advise applying masking tape to the build area. The rough surface of the tape will provide enough adhesion for the first layer to stick and print almost without any warping.
Users using heated build platforms have quite a few options these days. The usual suspects are glass and aluminum build plates. For directly printing on glass or aluminum we advice user to apply glue-stick. A very thin layer will be sufficient to keep your print nicely in place. Another method is dissolving wood glue in water, you the consistency of the substance can be quite thin, a bit like milk. By applying just a few drops and smearing this out before you start heating the built plate will create a very thing layer which holds the PLA/PHA down very well. If applying this method, be careful that you don’t get your electronics wet.
Another method that works well with colorFabb PLA/PHA is polyimide tape, or Kapton tape. This tape is available as a very narrow strip or very wide strips which allow you to cover the build plate in one go. When the tape is applied correctly it can last for months.
TIP! Take your time leveling the bed and adjusting the the gap between 3d printer nozzle and build plate. A perfect first layer will is very important, especially for 3d prints with a large bottom layer. Having the nozzle set to close to the build plate will cause a pressure build up and as a result back flow in most hot ends.
TIP! PLA/PHA has very minimal warping tendencies, however if your printing parts which take up the maximum of you buildspace you might see some warping. If it’s very important that your part is perfectly flat than we suggest to turn down the fan that is cooling your part. This allows the material to slowly get rid of heat without warping. After a few centimeters you can turn on the cooling if the part needs it.
*3d printers have lots of different types of hot-end which makes it extremely difficult to give aan temperature advice. We feel our temperature advice holds for most 3d printers, but should be considered as a starting point for you to find the temperatures that work in you setup. Don’t be afraid to go either higher or lower then our advised temperatures if you feel your set-up needs this.
Downloads
TDS
Technical Datasheet colorFabb PLA/PHA
MSDS
SDS colorFabb PLA/PHA
- SKU
- CF285BLUEISHWHITE (3D Universe)
Vendor Pricing & Availability
3D Universe
Updated: 22 hours ago
$19.99
Free Shipping
Store links may be affiliate links: we may earn a commission at no extra cost to you.
Advertisement
Price history
Lowest price each day
$19.99
Collecting price history
We have one day of prices so far. The trend line appears after at least two days.
View as table
| Date | 3D Universe |
|---|---|
| Nov 18, 2026 | $19.99 |
colorFabb PLA/PHA Filament 2.85mm (750 g) - Blueish White / 2.85mm price history: the price has held at $19.99 since Nov 18, 2026. The lowest price we've tracked is $19.99 (Nov 18, 2026), and we've followed it since Nov 18, 2026.
Compare prices
Advertisement