Bambu Lab H3C: 9-Material Tool Changer 3D Printer

Description

The Bambu Lab H3C is a nine-tool, fully enclosed tool changer. Every material sits in its own pre-heated PrintTool, so a print can switch between nine filaments, or between a fine nozzle and a fast one, in about six seconds. There's no purge tower to speak of and no waiting for a single hotend to heat up and cool down. The AMS 3H filament system, dryer and all nine spools live inside the machine, so it takes the same desk space as a single-nozzle printer.

SwapTek™: nine tools, six-second switches

Each of the nine PrintTools has its own filament path and heating system. Every material stays loaded, pre-heated and ready, so changing material takes six seconds instead of minutes, with far less waste than a single-nozzle multi-color printer.

FlexFeed: soft TPU at up to 3× the flow

The H3C runs both 1.75 mm and 2.85 mm filament (2.85 mm through the bypass feed) and switches between them on the fly. Thicker 2.85 mm TPU stays stiff under pressure, so TPU as soft as 75A prints reliably at up to three times the flow rate of a standard 1.75 mm setup. That makes it practical for soles, grips, gaskets and wearables. Shop Bambu Lab TPU 75A (2.85mm) in ten colors.

Mixed nozzles: detail and speed in the same print

On a single-nozzle printer you choose between a 0.2 mm nozzle for detail or a 0.4 mm nozzle for speed. With nine tools you don't have to: use a larger nozzle for the bulk of the part and a fine one only where detail matters. The H3C supports 0.2, 0.4, 0.6 and 0.8 mm hardened-steel nozzles.

AMS 3H: filament handling built for a tool changer

Push it in. That's it. Insert filament into any of the nine slots, and the AMS 3H detects it, routes it and loads it into the PrintTool on its own. RFID reads Bambu Lab spools automatically.

Dries while you print. A two-slot dryer in the filament bay heats to 85 °C, hot enough for PA, PC and carbon-fiber-filled engineering materials. The sealed bay actively removes moisture and shows temperature and humidity on the printer, in Bambu Studio and in Bambu Handy.

Nine materials, one footprint. Most multi-material setups end up with spools hanging off the sides and a dryer on the bench. The H3C keeps everything inside, in the footprint of a single-nozzle machine.

Flagship performance, easy to run

Lighter head, faster prints. A 40% lighter toolhead and X-axis assembly reach 25,000 mm/s² acceleration and 1,400 mm/s travel without ringing. Bambu Lab says prints finish over 10% faster.

Nine tools, aligned every time. Before every print, the H3C calibrates docking, tool offsets and bed leveling for all nine PrintTools, so there's nothing to tune by hand.

The fix, on screen. The Health Management System names the cause of a problem in plain language instead of an error code, and MiniWiki walks you through the fix step by step on the printer's touchscreen.

What you can make

Examples from Bambu Lab and MakerWorld creators:

Good to know before you buy

Power: the US (110–120 V) model draws up to 1,850 W for 3–5 minutes while the bed heats, and about 240 W printing PLA or 540 W printing PC after that. Plan for a dedicated 20 A circuit, or turn on Low Power Mode (1,050 W max), which heats the bed and chamber more slowly.

Space: the printer with AMS 3H measures 493 × 571 × 587 mm. Bambu Lab recommends 593 × 1,056 × 1,306 mm of clearance, and it ships in a 600 × 630 × 700 mm box at 36.28 kg (80 lb).

Network: Wi-Fi 6 only. There is no Ethernet port, network kill switch or 802.1X support, so check with your IT team if you're buying for a school or company network.

Room: operating temperature 10–30 °C.

What's in the Box (H3C Combo)

Bambu Lab H3C 3D Printer

AMS 3H (9-spool fully enclosed filament system)

9 × PrintTools (8 × 0.4 mm for 1.75 mm filament, 1 × 0.4 mm for 2.85 mm filament)

Textured PEI flexible build plate

Starter accessories, tools, and documentation

Specifications

Build volume (L × W × H)
330 × 320 × 325 mm

Tool changer
Bambu Lab SwapTek™ 9-Tool Switching

Enclosure
Fully enclosed; steel chassis

Nozzles
Hardened steel; 0.4 mm included; 0.2, 0.4, 0.6 and 0.8 mm supported

Max nozzle temperature
350 °C

Max bed temperature
120 °C

Active chamber heating
Up to 65 °C

Max toolhead speed / acceleration
1,400 mm/s / 25,000 mm/s²

Max hotend flow
40 mm³/s (Bambu Lab ABS at 280 °C)

Filament diameter
1.75 mm; 2.85 mm (bypass feed only)

Supported filaments
PLA, PETG, PCTG, TPU, EVA, PE, PP, PHA, PVA, BVOH and support filament; ABS, ASA, HIPS, PA, PAHT, PC, PET, PPA, PPS; carbon/glass-fiber-reinforced PLA, PETG, ABS, ASA, HIPS, PA, PAHT, PC, PET, PPA and PPS

Build plates
Textured PEI flexible steel plate included; also supports Cool Plate SuperTack and Engineering Plate

Air filtration
H11 HEPA plus granulated coconut-shell activated carbon

Cameras
Live view and toolhead cameras (1920 × 1080); optional BirdsEye camera (3264 × 2448)

Sensors
Door, filament run-out, nozzle clumping, filament odometry, power-loss recovery

Expansion
CraftTool support (CutTool, Draw

SKU
PF008-P+SA017-US (3D Universe)

Vendor Pricing & Availability

3D Universe

Updated: 1 hour ago

$2,499.00

Free Shipping

Buy Now →

Store links may be affiliate links: we may earn a commission at no extra cost to you.

Advertisement

Price history

Lowest price each day

$2,499

Collecting price history

We have one day of prices so far. The trend line appears after at least two days.

View as table
Date 3D Universe
Nov 17, 2026 $2,499

Advertisement

Zeb · 1d ago

Message hidden until you log in.
B

bob · 1d ago

Message hidden until you log in.
B

bob · 1d ago

Message hidden until you log in.
B

bob · 1d ago

Message hidden until you log in.
B

bob · 1d ago

Message hidden until you log in.
B

bob · 1d ago

Message hidden until you log in.

Eck · 23h ago

Message hidden until you log in.

7 recent messages, hidden until you log in. Log in or sign up to read the chat and join in.

Send private messages to other members.

Log in